Mastering Plumbing Fundamentals When You Install a Bathtub
Mastering Plumbing Fundamentals When You Install a Bathtub
Blog Article
We've noticed this great article involving How to Install a Bathtub below on the web and thought it made good sense to discuss it with you in this article.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a bathtub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is likewise a reasonably challenging task. If the old tub is conveniently available, the task can move easily; if you have to open up a wall surface to eliminate the old tub and position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub and embeded in the new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to hiring a service provider to take control of a halfway-completed job, it is far better to think about using one prior to you start. Possibilities are you might need a specialist plumber to make tube links.
This post will assist you install a new bath tub in your restroom if you have actually already purchased a brand-new tub and also don't need to alter the arrangement of your previous water supply pipelines.
Your tools as well as material list need to comprise the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water. After doing so, activate the faucets to drain any water continuing to be in the system. The process of eliminating the existing taps can be fairly troublesome because of the limited access that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the remaining water that will come from the pipes. Once the supply pipelines have been eliminated, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Prior to moving on to fit the new taps, compare the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will need a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making sure that the washing machines are in place in between the faucet and the sink. Safeguard the faucet in position with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous kind needs to be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level as well as adjusting the feet on the bath tub till the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression sign up with; then do the same for the other faucet.
Switch on the supply of water as well as examine all joints and new pipework for leaks as well as tighten them if necessary. Fill the bathtub as well as likewise inspect the overflow outlet and the regular electrical outlet for leakages.
Ultimately, take care of the bath paneling as defined in the maker's user's manual. Tiling and also sealing around the tub ought to wait until the bathtub has been utilized a minimum of when as this will settle it right into its final placement.
Planning for the Setup
Firstly, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to avoid strain on the bathtub.
Fit the adaptable tap adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you use all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a stiff seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, causing problems with wetness and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to permit the activity experienced when the tub remains in use. The sealer can crack rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily offered on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that write-up about A Step-by-Step Guide to Installing a Bathtub through a friend on another blog. Sharing is caring. Helping people is fun. I appreciate reading our article about How to Install a Bathtub.
Estimating Report this page